STRUCTURAL CARACTERIZATION OF MECHANICALLY AMORPHISIZED LiCa(PO3)3 and Al(PO3)3 USING HIGH RESOLUTION SOLID-STATE NUCLEAR MAGNETIC RESONANCE

Vol 2, 2025 - 327601
Oral and Poster
Favorite this paper
How to cite this paper?
Abstract

A new glass state of LiCa(PO3)3 and an amorphous state of Al(PO3)3 were successfully obtained from their respective crystalline phases via high-energy mechanical milling using Planetary Ball Milling (PBM) [1]. This solid-state process was developed at room temperature. X-Ray Diffraction confirmed the progressive amorphization of both crystals, as indicated by the gradual disappearance of diffraction peaks and the emergence of a broad halo, the latter being characteristic of amorphous materials. 31P, 7Li and 27Al solid-state Nuclear Magnetic Resonance (NMR) techniques were applied in samples of LiCa(PO3)3 and Al(PO3)3 subjected to different milling times. The evolution of the high-resolution 31P-NMR spectra demonstrates progressive amorphization of the structures in the milled samples. For both samples, the spectra exhibit two sets of resonances: narrow peaks corresponding to the P sites in the crystalline phase, and a broad peak characteristic of a disordered structure. The broadening of the 31P resonance from the crystallographic sites indicates the generation of defects on the crystal. The total collapse of the crystal peaks for milling times above 32 hs. confirms that the final milled product is completely amorphous. The resonance line from the amorphized material can be attributed essentially by PO4 tetrahedra with two O-P-O covalent bonds, namely Q2 phosphate unit (95 %). For LiCa(PO3)3, comparison with a melt-quenched (MQ) glass of the same composition, using 31P and 7Li-NMR, showed structural equivalence between both, based on similar chemical shifts, line widths, and Qⁿ distributions. Additionally, temperature-dependent static 7Li-NMR measurements on both milled and MQ samples demonstrated similar Li+ ionic dynamics, evidenced by the motional narrowing of the 7Li-NMR resonance line, suggesting comparable Li+ activation energies. For Al(PO3)3, 27Al-NMR and 3Q-MAS shows the appearance of new Al sites in the amorphous material in coordinations IV, V and VI, with the original Al (VI) site in the starting crystal disappearing in the final milled sample. Also, 31P-NMR shows that the new amorphous Q2 line present in this material appears around 20 ppm distant of the Q2 line of the starting crystalline material. This indicates a possible transformation from 4-membered phosphate rings in the crystal phase to chain-like structures in the amorphous phase. Thus, 31P, 7Li and 27Al-NMR demonstrate that the final products of both PBM crystals are disordered solids, with Al(PO3)3 exhibiting a structure completely distinct from its original crystalline form. PBM is known to induce amorphization in a variety of materials; However, Differential Scanning Calorimetry (DSC) analysis of the fully amorphous LiCa(PO3)3 revealed a very specific characteristic of the state of this material: the calorimetric signature of a glass transition and a crystallization event, both present in the glass state. This observation challenges the classical definition of the glassy state, which is considered as the result of supercooling a liquid to a state of extremely high viscosity that is unable to attain the lowest energy configuration associated to the crystalline state [2]. Therefore, this mechanical method opens the possibility of achieving a structural and thermodynamic state equivalent to glass, starting from a crystalline solid at room temperature in the macroscopic scale. In contrast, the DSC of the Al(PO3)3 sample with the longest milled time does not show any glass transition temperature. PBM is an effective technique to produce fine powders with controlled granulometry and high surface area. This method is employed in the fabrication of electrolytes in solid-state Li-ion batteries. However, the amorphization of certain materials under PBM can often lead to a reduction in Li ion mobility within the structure, which is undesirable for applications requiring high ionic conductivity. To counterbalance this trend, the controlled partial recrystallization of the amorphous phase can lead to the formation of vitroceramics—materials that combine the mechanical and chemical stability of glasses with the favorable ionic conductivity of crystalline phases. In this way, glasses produced by PBM at room temperature can be effective precursors for vitroceramics electrolytes, offering a more accessible and energy-efficient alternative to the traditional melt-quench techniques. This work provides compelling evidence of the mechanical amorphization of two phosphates by PBM, with one also vitrifying through a low temperature pathway, in contrast to the conventional melt-quenching methods.

Share your ideas or questions with the authors!

Did you know that the greatest stimulus in scientific and cultural development is curiosity? Leave your questions or suggestions to the author!

Sign in to interact

Have a question or suggestion? Share your feedback with the authors!

Institutions
  • 1 University of São Paulo
  • 2 Universidade de São Paulo
Track
  • 3 - Materials
Keywords
solid-state nuclear magnetic resonance
mechanical milling
glass transition