Structural Characterization of Irradiated ZnSb and ZnSb + InSb Films Deposited by Magnetron Sputtering

- 342418
Oral talk
Favorite this paper
How to cite this paper?
Abstract

ZnSb is of great relevance in thermoelectric research due to its good thermoelectric performance[1] and the relative abundance of Zn. Among the various crystalline phases that ZnSb presents, the β-Zn4Sb3  is of particular interest due to its high thermoelectric performance, even though it has stability issues[2], partly decaying to ZnSb when heated. Such issues can be resolved by doping the material with In. InSb on the other hand, in addition to its good thermoelectric properties[3], becomes porous when irradiated with swift heavy ions[4]. Porosity increases the effective surface area and can be of great advantage for the development of devices that rely on surface reactions. The effect of mixing InSb and ZnSb is not well understood yet, in particular, how the mixture behaves under ion irradiation, how the thermoelectric properties of ZnSb are affected and if the InSb present in the mixture can still become porous under ion irradiation.

In this work, films of ZnSb and ZnSb + InSb were deposited by magnetron sputtering and annealed in 523 K for 1h in a vacuum of 10-6 mBar, subsequently the samples were irradiated with 8 MeV Au ions to a total fluence of  1x1014 cm-2. The resulting films were analysed by grazing incidence X-ray diffraction (GIXRD), X-ray photoelectron spectroscopy (XPS), particle induced X-ray emission (PIXE) and Rutherford backscattering spectrometry (RBS) to determine the crystalline phases, the composition of the surface and the atomic distribution of the resulting films.

          For samples with higher In concentration, the RBS analysis showed that the films were composed of a main layer containing Zn, Sb and In plus oxygen with a thin layer of Zn and O close to the SiO2/Si substrate. In addition, for all samples, a thin layer of ZnO was observed on the surface, as corroborated by XPS.

           GIXRD shows both InSb zincblende and β-Zn4Sb3 phases are present, the later is a low temperature polymorph of the β-Zn4Sb3 phase that is expected to form at room temperature.

          The effects of ion irradiation on the atomic distribution and crystalline structure of the films are shown. 

 

References.

[1]       L. T. Zhang, M. Tsutsui, K. Ito, e M. Yamaguchi, “Thermoelectric properties of Zn4Sb3 thin films prepared by magnetron sputtering”, Thin Solid Films, v. 443, n. 1–2, p. 84–90, out. 2003, doi: 10.1016/S0040-6090(03)00855-1.

[2]       H. Yin, M. Christensen, B. L. Pedersen, E. Nishibori, S. Aoyagi, e B. B. Iversen, “Thermal Stability of Thermoelectric Zn4Sb3”, J. Electron. Mater., v. 39, n. 9, p. 1957–1959, set. 2010, doi: 10.1007/s11664-009-1053-3.

[3]       M. Jin et al., “Fabrication of InSb crystal via Horizontal Bridgman method and investigation on its thermoelectric properties”, Mater. Res. Bull., v. 142, p. 111411, out. 2021, doi: 10.1016/j.materresbull.2021.111411.

[4]       R. Giulian et al., “Ion irradiation-induced polycrystalline InSb foam”, J. Phys. Appl. Phys., v. 50, n. 48, p. 485104, dez. 2017, doi: 10.1088/1361-6463/aa920f.

Share your ideas or questions with the authors!

Did you know that the greatest stimulus in scientific and cultural development is curiosity? Leave your questions or suggestions to the author!

Sign in to interact

Have a question or suggestion? Share your feedback with the authors!

Institutions
  • 1 Universidade Federal do Rio Grande do Sul(UFRGS)
  • 2 Institute of Physics - UFRGS
  • 3 Universidade Federal do Rio Grande do Sul
Track
  • Nanostructured and semiconductor materials
Keywords
Thermoelectric
ZnSb
InSb
Irradiation