Para citar este trabalho use um dos padrões abaixo:
Films composed by proteins and polysaccharides play an important role in reducing the use of synthetic plastic materials. Usually, these biological materials form films with good mechanical strength and low oxygen permeability, however, due to their hydrophilic nature, they also present low water vapor permeability (WVP) and high sensitivity to ambient humidity. These properties can be improved incorporating hydrophobic components into the biopolymeric matrix, such as emulsions. Considered a low-cost source of vegetable protein, cowpea protein concentrate (CPC) was used in the present study with the aim at to form CPC-based films reinforced with a CPC-oil-in-water (O/W) emulsion and evaluate the impact of the addition of the lipophilic component on the films’ solubility and WVP. Briefly, O/W emulsions were prepared by adding sunflower oil, at a concentration of 10% (w/w), in an aqueous solution with pH 8 containing 0.6% CPC (w/w). The dispersion was homogenized using an Ultra-Turrax (T18 basic, IKA, Brazil) at 7,000 rpm/5 minutes and re-homogenized in a high-pressure homogenizer (APV, Homolab 2000, United Kingdom) at 300 bar. For control films (without emulsion addition), CPC (5%, w/w) and glycerol (30 g/100 g of CPC) were dissolved in distilled water, pH was adjusted to 8, the mixture was stirred and heated at 80°C/30 minutes in magnetic stirrer (NI 1107, Nova Instrumentos, Brazil). Reinforced films were prepared at the same way, however, after the heating step, the emulsion was added to the film-forming solution (0.5%, w/w) such that the oil concentration corresponded to 1% of protein, and then, the mixture was homogenized at 10,000 rpm/5 minutes. The film-forming solutions were cast on plane molds and dried at 35°C in a BOD incubator chamber (BT 71, Biothec, Brazil). WVP was determined according to the methods established by the ASTM E96-95 standard. For water solubility (WS) determination, films were immersed in distilled water at ambient temperature for 24 hours. Then, the wet samples were dried at 60°C in a vacuum oven until constant weight. It was expected that the addition of hydrophobic lipids to a hydrophilic protein film would improve WVP property. However, in the present work, the WVP wasn’t affected significantly by the emulsion incorporation. Permeability values were (8.51±0.04)×10-10 and (8.93±0.85)×10-10 g∙m-1∙s-1∙Pa-1 for the films with and without the lipophilic component addition, respectively. As in this case a major part of the continuous phase is occupied by hydrophilic components (glycerol/CPC), the small portion occupied by the oil droplets was not able to significantly slow the water transfer rate. On the other hand, the lipid presence in the protein matrix diminished the WS from 43 to 36%. This result was attributed to the non-polar components present in the sunflower oil, which would interact with non-polar sites of some amino acids, leading to a significant reduction of the protein capacity to interact with water molecules. It is concluded that the incorporation of 1g oil/100g protein to the film, though did not have improved the WVP, was able to enhance the water resistance of these films.
Com ~200 mil publicações revisadas por pesquisadores do mundo todo, o Galoá impulsiona cientistas na descoberta de pesquisas de ponta por meio de nossa plataforma indexada.
Confira nossos produtos e como podemos ajudá-lo a dar mais alcance para sua pesquisa:
Esse proceedings é identificado por um DOI , para usar em citações ou referências bibliográficas. Atenção: este não é um DOI para o jornal e, como tal, não pode ser usado em Lattes para identificar um trabalho específico.
Verifique o link "Como citar" na página do trabalho, para ver como citar corretamente o artigo